Blancco Drive Eraser can detect, remove and erase hidden areas from drives kann versteckte Bereiche von Laufwerken (HPA, DCO) . The handling of such areas is sometimes difficult and may produce some exception messages in the reporterkennen, entfernen und löschen. Der Umgang mit solchen Bereichen ist manchmal schwierig und kann im Bericht zu einigen Ausnahmen führen:
# |
Ausnahme |
Erläuterung | |
1 | HPA / DCO |
This message informs that the hidden area(s) was (were) detected and removed.
By “removed”, one must understand that the area was retired/suppressed, therefore it is not on the drive anymore.
2
HPA/DCO area content was erased
This message informs that the hidden area(s) content was erased.
By “erased”, one must understand that the area content was overwritten/wiped and does not contain data anymore.
These messages describe the cause of a problem:
- The software has executed a command to remove the hidden area(s), the command has failed.
- The software cannot reach the hidden area(s) of the drive.
This may be due to the following:
- The hidden areas exist but they are somehow locked and cannot be accessed.
The hidden areas simply don’t exist, however because we are not certain of this we assume they exist.3b
HPA/DCO area is unreachable
4
HPA/DCO area could not be removed
This message describes a direct consequence of the problem #3: the software cannot remove the hidden area(s) of the drive (because it is unreachable).
By “could not be removed”, one must understand that the area cannot be retired or suppressed, therefore it may still exist on the drive.
5
HPA area content could not be erased
This message describes another potential problem: the software cannot erase the contents of the hidden area(s) of the drive. This happens if the drive does not implement any command that can erase it as a whole, or if such command has not been used during the erasure.
By “could not be erased”, one must understand that the area content was not overwritten or wiped, therefore it may still contain data.
Some combinations:
...
Bereich entfernt | Diese Nachricht informiert darüber, dass die ausgeblendeten Bereiche erkannt und entfernt wurden. | |
2 | Inhalt des HPA / DCO-Bereichs wurde gelöscht | Diese Nachricht informiert darüber, dass der Inhalt der versteckten Bereiche gelöscht wurde. |
3a | Firmware-Befehl ist fehlgeschlagen oder kann nicht ausgeführt werden | Diese Nachrichten beschreiben die Ursache eines Problems: |
3b | HPA / DCO-Bereich ist nicht erreichbar | Dies kann auf Folgendes zurückzuführen sein: |
4 | HPA / DCO-Bereich konnte nicht entfernt werden | Diese Nachricht beschreibt eine direkte Konsequenz des Problems # 3: Die Software kann die versteckten Bereiche des Laufwerks nicht entfernen (weil es nicht erreichbar ist). |
5 | Inhalt des HPA-Bereichs konnte nicht gelöscht werden | Diese Nachricht beschreibt ein weiteres potenzielles Problem: Die Software kann den Inhalt der verborgenen Bereiche des Laufwerks nicht löschen. Dies geschieht, wenn das Laufwerk keinen Befehl implementiert, der es als Ganzes löschen kann, oder wenn ein solcher Befehl während des Löschens nicht verwendet wurde. |
Einige Kombinationen:
- Im Normalfall werden die Nachrichten 1 + 2 angezeigt.
- Trotzdem können Berichte die Nachrichten 3a / 3b + 4 + 5 auf einigen Laufwerken anzeigen, diese Kombination tritt auf, wenn während des Löschvorgangs kein Befehl verwendet wurde, der das Laufwerk als Ganzes löschen kann (der verborgene Bereich wurde nicht entfernt und sein Inhalt nicht gelöscht, d.h. der Bereich kann noch Daten enthalten).
- Andere Berichte können stattdessen die Nachrichten 3a / 3b + 4 + 2 anzeigen, diese Kombination tritt auf, wenn das Laufwerk einen Befehl implementiert hat, der es als Ganzes löschen kann und wenn dieser Befehl während des Löschvorgangs ausgeführt wurde (der versteckte Bereich wurde nicht entfernt, aber sein Inhalt wurde gelöscht, d.h. der Bereich enthält keine Daten).